1mm HDPE Mining Liner

1. Unmatched Compressive Strength for Deep Heap Leach Pads

2. Superior Chemical Resistance in Aggressive Leaching Environments

3. Dramatic Space Savings and Increased Ore Capacity

4. Fast, Safe Installation on Steep Canyon Slopes

5. Permanent Clog Resistance Through Engineered Filtration

Product Details

Not every mining project requires 2.0mm liner. Heap leach pads with low hydraulic head. Evaporation ponds. Collection trenches. For these applications, the 1mm HDPE Mining Liner provides reliable containment at a lower material cost. At 1.0mm (40 mils) thick, this material offers adequate puncture resistance for prepared subgrades while remaining flexible and easy to install. The black color comes from carbon black added for permanent UV protection. The smooth surface allows clean welding. For mining operations where 1.5mm or 2.0mm material is over-specified, the 1mm HDPE Mining Liner delivers cost-effective performance. This guide covers specifications, field applications, and purchasing considerations.


1mm HDPE Mining Liner1mm HDPE Mining Liner1mm HDPE Mining Liner


Product Overview

The 1mm HDPE Mining Liner is manufactured from virgin high-density polyethylene resin with carbon black content held at 2.0-3.0% for permanent UV stabilization. The 1.0mm nominal thickness provides a balance of mechanical strength and cost efficiency that makes it suitable for moderate mining containment applications .

As a 1mm HDPE Liner, this product offers permeability below 1.0×10⁻¹³ cm/s. Leachate and process solutions do not migrate through the liner. The material is produced via flat-die extrusion, ensuring consistent thickness across the full sheet width. Tensile strength at yield for 1.0mm material is approximately 15 kN/m, with puncture resistance reaching 320 N per ASTM D4833 .

The HDPE Membrane is available in smooth finish as standard, with textured options available for slope applications. For mining operations where 1.5mm or 2.0mm material is not required, the 1mm HDPE Mining Liner provides a cost-effective alternative that meets GRI-GM13 specifications .


Product Features

Permanent UV Protection. Carbon black is compounded throughout the resin at 2.0-3.0%. This is not a surface coating. The 1mm HDPE Mining Liner maintains UV resistance even if the surface is scratched during installation . For exposed heap leach pads and evaporation ponds, this protection is essential.

Near-Zero Permeability. The coefficient of permeability measures below 1.0×10⁻¹³ cm/s. Leachate and process solutions do not migrate through the 1mm HDPE Liner .

Broad Chemical Resistance. The 1mm HDPE Mining Liner withstands exposure to sulfuric acid, cyanide solutions, and typical mining leachates. No swelling, softening, or cracking occurs under normal operating conditions .

Good Puncture Resistance. At 1.0mm thickness, puncture resistance reaches approximately 320 N per ASTM D4833. This handles subgrade conditions typical of prepared mining sites . For coarse or angular subgrades, a geotextile cushion layer is recommended.

Excellent Tensile Properties. Tensile strength at yield is 15 kN/m, with break strength reaching 27 kN/m. Elongation at break exceeds 700%, allowing the HDPE Membrane to accommodate subgrade settlement without rupture .

Lightweight Construction. The 1mm HDPE Mining Liner is significantly lighter than thicker alternatives. One person can move a roll. No heavy equipment required for smaller mining applications.


Product Advantages

Lower Material Cost Than Thicker Options. The 1mm HDPE Mining Liner costs significantly less per square meter than 1.5mm or 2.0mm alternatives. For large heap leach pads covering many hectares, the savings can reach hundreds of thousands of dollars. Many mining applications do not require extra thickness.

Easier Handling and Installation. A roll of 1mm HDPE Liner weighs noticeably less than an equivalent roll of 1.5mm or 2.0mm material. Freight costs drop. On site, crews can move rolls with smaller equipment. Installation goes faster .

Faster Field Welding. Field crews report that 1.0mm material reaches optimal welding temperature more quickly than thicker geomembranes. The smooth surface prevents air entrapment under the weld bead. Production rates increase, and project schedules shorten .

Proven in Mining Applications. A mining operation in Kazakhstan used over 925,400 square meters of 1mm HDPE liner for gold processing facilities. The material was installed using hot gas and hot wedge welding equipment, demonstrating its viability for large-scale mining projects .

Regulatory Acceptance. Leading HDPE Liner Manufacturers produce 1.0mm HDPE geomembranes that meet GRI-GM13 and ASTM standards. The 1mm HDPE Mining Liner is accepted for moderate mining containment applications where 1.5mm or 2.0mm is not specified .


Technical Specifications

Parameter 1.0mm ValueTest Method
Nominal Thickness 1.00 mm ±0.10 ASTM D5199
Density ≥0.940 g/cm³ ASTM D1505
Carbon Black Content 2.0-3.0% ASTM D4218
Tensile Strength at Yield ≥15 kN/m ASTM D6693
Tensile Strength at Break ≥27 kN/mASTM D6693
Elongation at Break ≥700% ASTM D6693
Tear Resistance ≥125 N ASTM D1004
Puncture Resistance ≥320 N ASTM D4833
Stress Crack Resistance ≥300 hours ASTM D5397
Permeability <1.0×10⁻¹³ cm/s ASTM E96
Roll Width 3.0m to 8.0m Custom
Roll Length 50m to 200m Custom

Note: Values based on GRI-GM13 and ASTM standards from multiple manufacturer specifications .


Mining Applications

Heap Leach Pads (Low Hydraulic Head). For heap leach applications with hydraulic head typically less than 1 meter, the 1mm HDPE Mining Liner provides reliable containment . Gold and copper operations using passive heap leaching can specify 1.0mm material where loads are moderate.

Evaporation Ponds. Mining operations use evaporation ponds to concentrate process solutions. The 1mm HDPE Liner provides the chemical resistance and UV protection required for these exposed applications. The lightweight material is easier to handle than thicker alternatives.

Collection Trenches. Within heap leach pads, collection trenches gather pregnant solution. The 1mm HDPE Mining Liner lines these trenches, ensuring solution capture rather than loss to subgrade.

Solution Storage Ponds. Mining operations store process solutions in lined ponds. The 1mm HDPE Mining Liner provides a cost-effective barrier for applications where 1.5mm or 2.0mm material is not required.

Secondary Containment. Tank farms and chemical storage areas at mine sites use the 1mm HDPE Liner for secondary containment. The material provides reliable spill protection at a lower cost than thicker alternatives.


Comparison with 1.5mm and 2.0mm Options

The 1mm HDPE Mining Liner sits below 1.5mm and 2.0mm options. Each has its place.

1.0mm works for low-head heap leach pads, evaporation ponds, and collection trenches. It costs less and handles less puncture risk. Puncture resistance is 320 N .

1.5mm works for higher-load applications where additional puncture resistance is needed. Puncture resistance is 480 N.

2.0mm works for critical heap leach pads and tailings storage facilities. Puncture resistance is 640 N .

The 1mm HDPE Liner from established HDPE Liner Manufacturers provides adequate performance for many mining applications at a lower price point.


Packaging and Transport

The 1mm HDPE Mining Liner is wound onto heavy-wall cardboard cores with minimum 200mm inner diameter to prevent core collapse during crane lifting. Each roll is wrapped in opaque white polyethylene film with UV inhibitors to protect the outer wraps during storage and transit .

Corner protectors are fitted to both roll ends. The wrapped roll is secured to a hardwood pallet using steel strapping with edge protection .

For ocean freight, rolls are loaded into 20-foot or 40-foot containers. Palletized rolls are braced with inflatable dunnage bags or dimensional lumber to prevent shifting during transit. Rolls that exceed standard container dimensions ship on flat-rack containers

Shipping documentation includes commercial invoice, packing list, and certificate of analysis. Third-party inspection reports from SGS, Bureau Veritas, or TÜV are available on request .


Company Profile

The manufacturing facility operates multiple extrusion lines dedicated to HDPE Membrane production. Daily output supports large-scale mining projects. Production uses 100% virgin resin with no recycled content .

The facility is certified to ISO 9001, ISO 14001, and OHSAS 18001 standards. Finished product is tested to GRI-GM13 and ASTM specifications . Laboratory personnel perform physical property testing on every production lot.

As an established HDPE Liner Manufacturers supplier, the technical team has supported 1mm HDPE Mining Liner installations across heap leach pads, tailings storage, and process ponds globally. Support includes installation guidance, welding procedure specifications, and on-site troubleshooting .


1mm HDPE Mining Liner


Frequently Asked Questions

Q: Is 1.0mm thick enough for mining applications?

A: For low-head heap leach pads (hydraulic head less than 1 meter), evaporation ponds, and collection trenches, yes. The 1mm HDPE Mining Liner provides 320 N of puncture resistance. For high-load heap leach pads or tailings storage, 1.5mm or 2.0mm is recommended .


Q: How long does 1.0mm HDPE last in mining applications?

A: Properly manufactured and installed, the 1mm HDPE Liner has a service life exceeding 20 years for exposed applications. Covered liners last longer. Leading HDPE Liner Manufacturers offer warranties of 20 years for exposed applications and 50 years for buried applications .


Q: What chemical resistance does the liner provide?

A: The 1mm HDPE Mining Liner withstands exposure to sulfuric acid, cyanide solutions, and typical mining leachates. The material is tested for compatibility with aggressive mining liquors. For applications with elevated temperatures (above 60°C), higher-performance formulations may be required .


Q: Can this liner be installed in cold weather?

A: Yes. HDPE remains flexible at low temperatures. The 1mm HDPE Liner has a working temperature range from -70°C to 150°C . For cold weather installation, appropriate welding procedures should be followed.


Q: How are seams made in the field?

A: Thermal fusion welding using hot wedge equipment. The welder heats both sheet edges and presses them together. The smooth surface welds clean with no trapped air. Seam strength matches parent material .


Q: What subgrade preparation is required?

A: The subgrade must be smooth, compacted, and free of sharp objects, roots, and debris. Remove any stones larger than 12mm. For coarse or angular subgrades, place a geotextile cushion layer beneath the 1mm HDPE Mining Liner .


Q: What is the minimum order quantity?

A: For standard 1mm HDPE Liner, orders typically start at one 20-foot container. This represents approximately 8,000-10,000 square meters depending on roll configuration. Larger mining projects often order multiple containers .


Q: Can samples be obtained before ordering?

 A: Yes. Sample swatches of 1mm HDPE Mining Liner are available on request. Project-specific chemical compatibility testing is recommended when the liner will contact unusual mining solutions .


Q: What is the typical lead time for mining orders?

A: Standard orders ship within 7-15 days after confirmation. Large mining projects requiring significant quantities may require advance scheduling .


Summary

The 1mm HDPE Mining Liner provides cost-effective containment for moderate mining applications. The 1.0mm thickness delivers adequate puncture resistance for low-head heap leach pads, evaporation ponds, and collection trenches. The material offers permanent UV protection, broad chemical resistance, and near-zero permeability.

The 1mm HDPE Liner from established HDPE Liner Manufacturers meets GRI-GM13 and ASTM standards. The lightweight construction reduces freight costs and simplifies handling. Field welding is faster than with thicker alternatives.

For mining operations where 1.5mm or 2.0mm material is over-specified, the HDPE Membrane at 1.0mm provides reliable performance at a lower cost. Mining operators and procurement teams seeking a 1mm HDPE Mining Liner should contact the technical sales team with project specifications. A detailed quote, product samples, and installation guidance will follow.


Leave your messages

Related Products

x

Popular products

x
x